The Hoy Gummer
New Machine Installed by the Ashington Coal Co., Ltd.
In the summer of last year we had an opportunity of seeing a new machine
demonstrated at the works of Austin Hoy and Co., Ltd. This machine, or rather
part of a machine was designed to replace the gearhead on existing coal cutters
and provides additional units for collecting the cuttings and conveying these
away from the chain.
It is well known that the cutting side of the chain cleans the cut but that
much of the small coal is unable to escape from the chain which carries it back
and deposits it in the cut, behind the machine. The Hoy gumming gearhead was
devised to remove the entrained coal from the chain as it passes round the
driving sprocket.
This new gearhead thus differs in several important particulars from those
already in use. There is a skid plate on the base which makes the bottom of the
cutter, from haulage to gearhead one continuous flat surface. A centrifugal
disc is keyed to the bottom of the sprocket shaft and this disc revolves at
clearance distance above the skid plate. Since this disc is smooth it will be
clear that the coal entrained in the picks is thrown towards the edge of this
disc by centrifugal force. At the gob-side side of the machine a circular
baffle, which can easily be removed for pick setting, is provided to prevent
the cuttings being thrown out. The cuttings are removed from the disc by a
stationary plough.
This plough delivers the cuttings into a rotary shovel or elevator of simple
inclined paddle wheel formation. The drive for this elevator is taken from the
large gear on top of the sprocket driving shaft through an overload slipping
clutch of novel design. This elevator is arranged to run at the lowest speed
which will permit the whole of the cuttings being discharged by gravity. From
the elevator the cuttings fall into a chute and are delivered on to a small
belt conveyor driven from the elevator shaft. The diagram shows that this drive
is so arranged that the conveyor can he elevated or slewed to left or right.
This conveyor is held normally at its proper height by an adjustable chain
having a soft hook which yields under falls. The entire mechanism reverses
automatically — there are no controls — when the motor is reversed
for cutting back, cutting under being done with the rear elements attached. The
small conveyor, of course, is driven from the opposite corner when cutting
back.
From the foregoing description it will be seen that the basic principles of
this device are comparatively simple but considerable ingenuity has been
displayed in fitting them into those limits of space which coal face conditions
require. Despite these limitations, however, it has been possible to employ
factors of safety for each part which compare favourably with those common on
coal cutting machines.
We were recently permitted to see this new gearhead at work underground in one
of the Ashington Coal Co.'s pits. The machine was cutting in the Diamond seam
which is about 2 ft. 8 in. thick and, at the time of our visit was making the
fifth consecutive cut on a conveyor face 120 yd. long. We understand that
extensive trials have been made with this machine in other seams worked by the
Ashington Coal Co. in order to give as full a knowledge as possible of its
abilities and shortcomings. In the Diamond seam, however, cutting is done in
the coal and the conditions are good. During the whole of our visit the machine
worked perfectly.
We have not seen this particular face being cut by a normal machine and can,
therefore, only make general comparisons of the gumming machine and the
ordinary coal cutter. We travelled a considerable length of the face and
throughout the cut was clean. The height of the cut was 5 in. and it was
possible to see the back of the cut at any point on the face. There was a
uniform layer of dust or very small coal on the floor of the cut and this
appeared to be from ¾ in. to 1 in. thick. Nowhere was there any
accumulation under the cut.
The cuttings at this pit are of good quality coal and are loaded out for
screening and cleaning; thus the leaving of a small amount of the finest
fraction under the cut is an advantage since it avoids the difficulties which
might otherwise arise on the cleaning plant. The cuttings as loaded were coarse
and it is believed that these are coarser than the product from an ordinary
machine since they are subjected to no grinding action by the chain after
cutting.
On the machine the cuttings are kept in mass. They pile up on the bottom disc
and thanks to a slight reservoir action of the chute the delivery from the
elevator to the small conveyor is almost uniform. Since the conveyor is a belt
the cuttings on it remain stationary relatively to the belt and are fed in a
smooth stream on to the face conveyor. This careful handling not only prevents
the cuttings being further broken down but has the additional advantage of
minimising the dust nuisance. We understand that the face on which we saw this
machine working is not a dusty one but the atmosphere when the gummer was at
work was certainly clearer than is usual on the face during coal cutting. A man
gumming with a shovel has time to do no more than knock some of the cuttings
away from the chain and it seems probable that he must in that process create
more dust than is raised by the Hoy gummer. Indeed the only time the cuttings
are open to the action of the ventilating current is during the delivery from
the gummer to the face conveyer. Since the trajectory is only about 10 in. it
is clear that this period is a short one. Moreover if the machine were working
in a very strong air current a fabric hood could easily be fitted to keep the
cuttings enclosed.
We have already stated the gumming conveyor is pivoted in two planes; this
enables props to be passed with the minimum of spillage. The machine is run
until a prop pushes the gumming conveyer so far out of line that the coal is
delivered on to the edge of the face conveyor. The gumming conveyer is then
lifted and slewed past the prop, while the machine is in motion of course, and
only a few handfuls of coal are spilt against each prop.
This machine has one other very important advantage, that is the complete
enclosing of the chain. Many types of chain guard have been devised, but all of
these — so far as we know — are a nuisance to the man gumming at
the back of the machine, and have hence had a very short life. On the Hoy
gummer only about 2 in. of chain right up against the coal are visible, and it
would, we believe, be impossible for a man to be accidentally caught in the
picks. This total enclosing of the chain does not appear to add to the danger
of jamming since a momentary reversal has, so far, always released any
obstruction that may have got caught in the chain.
The addition of the disc, elevator, conveyor and necessary gearing which are
designed to handle up to 6 cwt. of coal or 12 cwt. of stone per min., requires
only about 2 h.p. to drive them, but it is believed that there will be, on the
whole, a reduction in the power required to drive the machine to which they are
fitted. It is obvious that there is a high power expenditure on a machine which
is not kept clear of cuttings owing to the chain churning up the coal. The
amount of power required for this purpose will depend upon the activities of
the gummers, and cannot easily be measured. Detailed tests have not yet been
carried out, but such measurements as have been made suggest that a saving of
power may be obtained by use of the Hoy gummer.
Among the other advantages which can he claimed for this machine is certainly a
saving of labour. One man at the back of the machine can easily do all that is
required. So far as the cutter is concerned, all he has to do is lift the
gumming conveyor past the props. He is thus able, in addition, to attend to the
supports set in the cut and on the face as necessary.
It also seems reasonable to assume that this thorough cleaning out of the cut
will have a beneficial effect on shotfiring. It is too early yet to evaluate
this benefit on the particular face when this machine is working at Ashington,
but we understand that a reduction in the requisite weight of charge is already
apparent. Obviously this reduction will depend on the particular circumstances
at any particular pit so that, even if they were available, it would be useless
to give the figures for one face. Not until further experience has been
obtained in other seams can useful generalisation be expressed.
This gumming gearhead can only be fitted to machines at least 15 in. high since
the elevator cannot be compressed into smaller dimensions. The minimum width is
30 in., and this gearhead can be fitted to coal cutters of most makes. As we
have already said the machine, on the occasion of our visit, was working
perfectly, and, an important point, the coal cutter staff like it. It appears
that the trials that have been made have already taken it through its teething
troubles, and we understand that units are being installed in the pits of some
other companies.
This machine introduces no additional complications on the face, but to get the
best use from it it may, at some pits, necessitate a minor reorganisation of
the face schedule. If the cuttings are worth loading, it is obviously more
efficient to load them direct on to the face conveyor than to put them on the
floor to be picked up again by the filling shift. The requisite haulage
arrangements should not, however, represent an insuperable difficulty. In any
case, the main point is that the gumming is got out of the cut.
We are glad to acknowledge our debt to the Ashington Coal Co., Ltd., for
permitting us to see this machine at work, and to several members of their
staff for assistance in the compilation of this account.